The electrical load a house is expected to carry has changed dramatically over the past few decades. A home wired for the appliances and lighting of an earlier era now runs EV chargers, home offices, high-draw kitchen equipment, and whole-house electronics. That gap between what the wiring was designed for and what the household actually needs is behind a large share of the calls we get in Nazareth and the surrounding area.
We handle that work here. Older homes with panels and circuits that have never been updated, newer builds adding capacity for a charger or a workshop, landlords keeping rental properties up to code, and property managers dealing with a fault that needs sorting before a unit turns over. Whatever the situation, the scope gets discussed on the phone before anything is scheduled, and the price is confirmed before the visit happens.
Call (484) 549-3289 to get the conversation started.
Out-of-hours electrical work at a commercial or light industrial property involves a different kind of planning than a residential job. The goal is often to keep one section of a building operational while another is being worked on. That means mapping which circuits feed which areas, confirming the panel can isolate the affected run without pulling power from the rest of the floor, and sequencing the work to minimize disruption.
We handle this kind of project for small manufacturing facilities, workshops, offices, and retail spaces. The planning conversation happens before the visit, not on arrival.
Commercial electrical work is priced after the scope is understood. That means asking the right questions on the call: what the building currently runs, what is being added or changed, and whether the existing panel and service entrance can carry the new load without an upgrade. A load calculation is part of that conversation for any job that adds significant draw to the panel.
We test every circuit. We label every breaker. We leave it safe.
When power goes out or a circuit stops working, the first question is whether the problem is on the property or on the utility side of the meter. Those two situations call for completely different responses, and mixing them up wastes time and money.
We start by checking the meter base, the main disconnect, and the panel. If the fault is upstream of the meter, that is a utility call, and we will tell you that plainly and explain what to report when you contact them. If it is on our side, we trace it from the panel out to the affected circuit or device. Intermittent faults, partial outages, and circuits that lose power only under load are all traceable with the right approach. Reach out and we will get it diagnosed.
A detached garage or workshop that runs power tools, a compressor, or a welder needs more than a single circuit run from the house. A subpanel fed from the main service gives the space its own breakers, its own capacity, and a proper ground. It also makes adding circuits later straightforward rather than a workaround. We size the subpanel feed based on what the space will actually draw, not just what it runs today.
Intermittent faults are the most time-consuming electrical problems to resolve, because the symptom disappears before anyone can test for it. A breaker that trips only when two specific appliances run at once, a circuit that loses power overnight and recovers by morning, or an outlet that works most of the time are all worth tracing properly rather than guessing at. We work through the circuit systematically, check connections at every termination point, and confirm the fix before leaving.
An outdoor outlet that is not in a weatherproof enclosure is a code problem and a safety problem. We install weatherproof GFCI-protected receptacles for exterior locations, whether that is a garage wall, a back porch, a workshop entry, or a garden area. The enclosure rating and the GFCI protection are both part of the installation, not add-ons.
A panel that has reached the end of its service life, a breaker that will not hold a reset, or a box that is out of space for new circuits all lead to the same conversation. We assess whether the issue is a single failed breaker or whether the panel itself needs to come out. If the service entrance is undersized for what the property now draws, that gets addressed at the same time. The homes and wiring in this area have their own quirks, and a panel that looked adequate ten years ago may not be now.
High-draw workshop equipment needs a dedicated circuit sized for its actual load, not a shared run that trips every time the compressor kicks on. A welder pulling significant amperage needs a 240-volt dedicated circuit with the right breaker rating and the right wire gauge for the run length. We size and install these circuits as standalone jobs or as part of a subpanel installation for a workshop or outbuilding.
One call is enough to get the visit booked.
The price for electrical work depends on three things: what the fault turns out to be, what has to be opened up or moved to reach it, and whether the existing circuit or panel can carry the change being made. A straightforward outlet replacement in an accessible location is a different job from tracing a fault through a finished wall in a home with original wiring.
When you call, we ask about the symptoms, the property, and what has already been tried. From that, we can give you a price range for most standard work before the visit is booked. For larger projects, a site visit is sometimes needed to scope the job accurately, and that conversation happens before anything is committed to. The scope of the electrical work is priced before it starts, so there are no questions about what the visit covers.
Book the visit. Know the scope. Know the price before it starts. Anybody planning ahead in Nazareth can start with our page of electrical services.
Electrical work done without permits, to outdated standards, or by someone working outside their depth shows up in specific ways. Wiring that is undersized for its circuit breaker, connections made with the wrong materials, GFCI protection missing where code requires it, or a panel with breakers doubled up on terminals that were never designed for it. These are not rare finds in older properties, and they are not cause for alarm. They are cause for a clear-eyed assessment.
When we find work that needs correction, we explain what it is, why it matters, and what it takes to bring it up to standard. We keep you informed from diagnosis to final test, so nothing happens without your understanding of what it involves. If something can be corrected in place, we say so. If it needs to come out and be redone, we say that too. The goal is an accurate picture, not a long repair list.
Electrical work here gets handled by people who answer to this community.
A burning smell near a panel, an outlet that is warm to the touch, or a breaker that will not hold a reset are not problems to leave until next week. We take short-notice calls and handle urgent electrical faults as a priority. When you call, describe what you are seeing and we will work out what the situation calls for. We are available every day from 7:30 AM to 9:30 PM.
A rental property with a tenant in place, or a business that cannot go dark for a full day, needs a different approach to scheduling. We discuss the constraints on the call and plan the work sequence around them. That might mean splitting the job across two visits, working in sections to keep part of the property live, or scheduling at a time that fits the tenant's hours. The aim is to get the work done without making the disruption worse than the fault itself.
We handle electrical work throughout Nazareth and the surrounding area in Northampton County. That includes Upper Nazareth Township, Lower Nazareth Township, Stockertown, Tatamy, and Eastlawn Gardens. Whether the job is a single circuit repair or a full panel replacement, the same process applies: the scope is discussed on the phone, the price is confirmed before scheduling, and the work is done to the standard the next inspection expects.
If you are not sure whether your address falls within our service area, call and ask. We confirm coverage on the phone.
Heat at the surface of a faceplate points to a problem at the connection behind it. Discoloration from heat is a sign the issue has been building for some time. Stop using the device and call us so we can open it up and find the cause.
Call and describe what you are seeing. Wiring that looks improvised, a panel with unusual modifications, outlets that have no ground, or breakers that are the wrong rating for their circuit are all worth having assessed. We look at what is there, explain what it means, and give you a clear picture of what needs to change and what can stay as is. Nothing is quoted or scheduled without your understanding of the scope first.
Homes in this part of Northampton County often have panels that were sized for a much lighter load than current demand places on them, along with wiring that predates modern grounding and circuit protection requirements. Knob-and-tube wiring, aluminum branch circuits, and double-tapped breakers all turn up regularly. When we assess an older property, we look at the panel, the wiring type, and whether the existing circuits can safely carry what is being asked of them.
Yes. An electrical safety inspection covers the panel, the circuits, the outlets, grounding and bonding, and GFCI and AFCI protection across the property. It is a useful step before buying a home, before listing one for sale, or when a landlord wants a clear picture of a unit's condition before a new tenancy.
Each typically requires its own dedicated 240-volt circuit. A wall oven and a cooktop are not wired from the same circuit the way a combined range is, so a kitchen being fitted with separate appliances may need two new circuits rather than one. We confirm the circuit requirements for each appliance before the work is scoped.
Yes. A circuit mapping visit identifies which breaker controls which outlets, fixtures, and appliances throughout the property. We label the panel clearly so that anyone working on the property or responding to a fault knows exactly what each breaker covers. This is particularly useful for older properties where the original labeling is missing or wrong.
Yes. We handle electrical work in Upper Nazareth Township, Lower Nazareth Township, Stockertown, Tatamy, and Eastlawn Gardens, as well as in Nazareth itself. Coverage for your specific address is confirmed on the call, and we can usually get a visit scheduled without a long wait.
Yes. Any breakers added or replaced during the visit are labeled before we leave. If the existing panel labels are missing or unclear, we address those as part of the same visit so the panel is readable going forward.
Northampton County is the area we serve, and Nazareth along with the communities around it are part of that coverage. Whether the job is in town or in Upper Nazareth Township, Lower Nazareth Township, Stockertown, or Tatamy, the call starts the same way. You describe the situation, we work through the scope with you, and you get a price before anything is scheduled. We are available every day from 7:30 AM to 9:30 PM.
Call Easton Electrical Company at (484) 549-3289 and we will get it on the schedule.
For every town we reach, see our complete service area. Also serving the towns around: Eastlawn Gardens, Palmer Heights, Chestnut Hill, Plainfield Township.
Below is a plain-language look at the electrical services we handle for homes and businesses in Nazareth and across Northampton County. Each row covers what the service includes, who it fits best, and one practical detail worth knowing before you call. If a job spans more than one category, we scope it together on the call so nothing gets missed.
| Electrical Service | What It Covers | Ideal For | Things to Know |
|---|---|---|---|
| Electrical Panel & Service UpgradesMost Popular | Panel replacement, Service-entrance upgrade, Subpanel installation, Load calculation | Homes adding major loads like an EV charger, or properties with a panel that fails inspection | A 60-amp or 100-amp service sized for a mid-century household often cannot carry modern loads. We confirm the right service size before any work is quoted. |
| Lighting Installation | Recessed and LED lighting, Security and motion lighting, Outdoor and landscape wiring, Commercial lighting upgrades | Homeowners updating interior lighting or businesses improving a retail or office space | Outdoor security lighting wiring runs from the panel out to the fixture. We handle the full circuit, not just the fixture swap. |
| Whole-Home Surge Protection | Panel-mounted surge protector, Whole-home coverage, Appliance and electronics protection | Homeowners with sensitive electronics or a new panel who want to protect downstream circuits | A panel-mounted surge protector covers circuits that a standard power strip suppressor cannot reach, including appliance controls and HVAC electrical boards. |
Call (484) 549-3289 and we will walk through the scope with you, confirm the price, and get the visit on the schedule.
(484) 549-3289